Does the clean workshop need to be equipped with sprinklers? And the setting of the fire sprinkler in the clean workshop
The sprinkler system is very important. For fire protection, it can prevent the spread of fire to a large extent and achieve the purpose of extinguishing fire, especially in the pharmaceutical cleanroom. Does the clean workshop need to be equipped with sprinklers? And the setting of the fire sprinkler in the clean pharmaceutical cleanroom? Below and sz -pharma Let's take a look together. 1. Does the clean workshop need to be equipped with spray? The clean workshop should be equipped with spray system software in accordance with the requirements of the construction regulations, but the spray standard has not established the fire accident hazard level of this type of industrial plant, and generally it is not allowed to set up spray Yes, but there are fire hydrants inside. If only a part of the industrial plant is a production line, the fire hydrants in the clean area and the non-clean area are not used at the same time, and the non-clean area is equipped with spray. The sprinkler system software is a mandatory specification for the fire safety of electronic clean workshops. In the total construction area, it is necessary to achieve a certain number of evacuation exits. However, it is turned off during specific operation, and the installation is only used for the acceptance of key fire safety projects. Your evacuation exits and gross floor area must be installed if mandatory. Is it mandatory to do spraying (whether it is wet test or dry test) in the pharmaceutical industry or electronic clean workshop? Chapter 8, Section 5 of the Regulations! Covering area of industrial plants of power plants>2500², no doubt with sprinkler. Generally, based on comprehensive considerations such as the production process of industrial plants, it may only be possible to consult fire safety units, and they are 'standards'. The hardware factory is generally sprayed, and the clean area uses quick-response nozzles or pre-effect system software. The clean area of the electronic device industrial plant is all sprayed, which is more important than the non-clean area. There is no standard in the standard about whether the clean room is equipped with a spray automatic fire extinguishing system, and spraying is not allowed in the cleaning process. See only to the local fire brigade to ask. The fire extinguishing system installed in the clean room is different from the traditional water spray and other dry powder fire extinguishers. The clean room fire extinguishing needs [158 fire 6363 fire 9II9 system] to formulate a solution for the situation of the clean room. There can be no dust in the clean room, so the fire extinguishing system There can be no residue after fire extinguishing, so it is suitable for gas fire extinguishing systems. There are the following suitable ones: 1. High pressure carbon dioxide fire extinguishing system (total submersion type/pipe network type/CO2) 2. Pipe network type heptafluoropropane prefabricated automatic fire extinguishing device 3. 1230 perfluorohexanone gas fire-extinguishing pharma machinery (higher degree of cleanliness 2. Setting of fire sprinkler in clean workshop 1. Upper sprinkler is used, that is, the sprinkler head is installed in the ceiling interlayer, and smoke detectors, fire hydrants, and smoke exhaust air outlets are installed in the workshop. This method is mostly used. 2. The sprinkler head is directly installed in the workshop, protruding from the ceiling, and it is easy to accumulate dust if it is not sealed. 3. The sprinkler head is installed in a decorative sleeve and is flush with the ceiling, and the sleeve has a special cover , The seal is good, the height of the sleeve is difficult to be consistent, and the appearance is slightly poor. Generally speaking, the installation methods of the upper spray and the lower spray are related to the fire protection level of the purification workshop. 3 is relatively more difficult to construct.
An increasing dependence on the use of CUSTOM SOLUTION SERVICES extraction machine has made numerous changes in the extraction machine industry over the past decades.
SUZHOU PHARMA MACHINERY CO.,LTD. supports these goals with a corporate philosophy of adhering to the highest ethical conduct in all its business dealings, treatment of its employees, and social and environmental policies.
SUZHOU PHARMA MACHINERY CO.,LTD. knows how important it is to offer optional extras, such as CUSTOM SOLUTION SERVICESextraction machine to provide quality products for customers.
There are many advantages associated with .
CUSTOM SOLUTION SERVICES has its grasp on oversees market and has a very good repute. Our products are available at very competitive prices.