Laboratory furniture installation project

furniture installation project

furniture is different from office furniture. Its use is often in contact with water, electricity, gas and equipment, which puts forward higher requirements on the structure and material of furniture; when laboratory construction, it must be aimed at the laboratory. According to the work content, environmental conditions and specific requirements, furniture design and...

Text label: laboratory construction, pharma machinery engineering, laboratory design

Furniture Installation Project

furniture is different from office furniture. Its use is often in contact with water, electricity, gas and equipment, which puts forward higher requirements on the structure and material of furniture; when laboratory construction, it must be aimed at the laboratory. According to the work content, environmental conditions and specific requirements, furniture design and selection. According to the function, it can be divided into experimental benches and experimental cabinets. Experiment benches include physical and chemical experimental benches, instrument benches, sky platforms, washing benches, dissection benches, reclaiming benches, high temperature benches, etc. Experiment cabinets include safety storage cabinets, utensil cabinets, and fireproof cabinets. , file cabinets, lockers, specimen cabinets, sample cabinets, gas cylinder cabinets, etc. According to different materials, it can be divided into wooden structure, steel-wood structure and all-steel structure; wood-based furniture materials are mainly wood-based panels, which are rich in color and strong in personalization, suitable for users who pursue individuality, but their moisture resistance and bearing capacity are slightly weaker. It is not suitable for humid laboratories and environments with high load-bearing requirements; the steel-wood structure is composed of a metal frame and a wooden cabinet, and the test bench can be equipped with a movable lower cabinet or a fixed cabinet, which is cost-effective and suitable for users who pursue economic benefits; steel The furniture is made of cold-rolled steel plate, with good load-bearing performance, strong and durable, and strong comprehensive performance, which is suitable for users with sufficient budget and high requirements.

For the installation of the full-rigid test bench, observe the front and side of the steel frame. All the joints of the beams and square tubes of the steel frame should not be placed on the visible surface. Mark the height of the cabinet on the steel frame or make a match with the cabinet. Barriers with the same height; according to the total length of the test bench, select the appropriate beam, and use self-drilling screws to fix the beam to the steel frame. The joint of the steel frame is horizontal, and its position affects the level of the table, the thickness of the gap between the drawing surface and the beam. When screwing, pay attention to the parallelism between the beams; on the premise of ensuring the level, the cabinet can be hung, and the horizontal type can be used. There are two methods of hanging the cabinet with the vertical steel frame. The method is basically similar. The supporting joist on the steel frame is screwed to the height of the cabinet hanging below the cabinet, and then put into the cabinet; 4*30 is used between each cabinet. Push the two ends of the cabinet to be flush with the two ends of the steel frame, tighten the nuts of the supporting joists with a wrench to make them fully bear the force; install the side sealing plates and fix them with small right angles and screws. Zhongjing Global Purification can provide consulting, planning, design, construction, installation, transformation and other supporting services for laboratories and clean rooms.

For the installation of the extraction surface and the door panel of the cabinet of the laboratory test bench, all the door gaps are uniform, ensure that the gap is not greater than 2mm, and the intersection of the horizontal and vertical lines is not in place; the vertical surface of the door panel and the extraction surface can be tested with a long straight strip ;Do not collide with the four sides when the door panel is opened and closed, and the hinge screws must be tightened to prevent the door panel from falling off; Whether the drawer is pulled smoothly and whether there is any abnormal sound, if the pull is not smooth, there may be two reasons, one is the cabinet body The positioning of the slide rails on the side panels is not accurate, and the second is that the screws are not correct; the steel-wood structure is usually installed with the drawing surface first, and then the table top is installed.

If you have a extraction machine business, be sure to choose a from SUZHOU PHARMA MACHINERY CO.,LTD.. After all, you need quality equipment in order to provide your customers with quality service.

SUZHOU PHARMA MACHINERY CO.,LTD. is a professional manufacturer of offering some of the best in class CUSTOM SOLUTION SERVICES solutions to global market. Click PHARMA MACHINERY to learn more.

We believe in keeping the customers happy and providing them with CUSTOM SOLUTION SERVICES at a very competent price.

SUZHOU PHARMA MACHINERY CO.,LTD. always believes that the average profitability of our company is sufficient.

Innovative technology helped us produce a strong, reliable product as CUSTOM SOLUTION SERVICES for customers, offer superior quality and dependability to our customers, and scale at a quicker pace.