What are the cost calculations for the decoration and installation cost of the purification workshop?1
The costs incurred during the renovation of our purification workshop are mainly based on the host system, terminal system, ceiling, compartment, floor, clarity, lighting and other requirements. Then there is the issue of purification level, and there will be quantitative standards for the decoration of purification workshops. The purification level is divided into one hundred, thousand, ten thousand and even higher. The editor of sz-pharma reminds that there is a point to pay attention to. The greater the value of the purification level, the lower the pharma machinery requirements. Let's take a look at the cost calculation of the decoration and installation cost of the purification pharmaceutical cleanroom! Interior decoration materials: 1. The moisture content of the wood used in the purification workshop shall not exceed 16% and shall not be exposed. The clean room has many times of ventilation and low relative humidity. If wood is used in large quantities, it is easy to dry, deform, loosen, and generate dust. It must also be used locally for anti-corrosion and moisture-proof treatment. 2. When using gypsum board in general purification pharmaceutical cleanroom, waterproof gypsum board must be used. However, because the biological purification workshop is often scrubbed with water and cleaned with disinfectants, even if the waterproof gypsum board is deformed by moisture, it is not resistant to washing, so it is stipulated that the biological purification workshop should not use gypsum board as a covering material. 3. Different purification workshops should also consider different individual needs when choosing interior decoration materials. 4. The purification workshop generally needs to be wiped frequently. In addition to scrubbing with water, wipe with disinfectant water and alcohol lamp solvent. These liquids usually have certain chemical properties, which can discolor and peel off the surface of some materials, which requires certain chemical resistance of decorative materials. 5. In biological purification workshops, such as operating rooms, in order to sterilize, a tri-oxygen generator is generally installed. It is a strong oxidizing gas, which can accelerate the oxidation and rust of objects in the environment, especially metals, and also make the surface of the general coating due to oxidation. And fade, so this kind of purification workshop requires decoration materials with good oxidation resistance. The reason for affecting the product quality in the decoration and construction of the purification pharmaceutical cleanroom is that there are problems in the process control link, and there are hidden dangers in the installation and construction process. ②The enclosure structure of the color steel plate is not tight, the sealing measures between the clean room and the technical interlayer (ceiling) are improper, and the airtight door is not sealed; ③The decorative profiles and process pipelines form dead corners and dust accumulation in the clean room; ④Individual locations do not meet the design requirements Construction, can not meet the relevant requirements and regulations; ⑤ The quality of the sealant used is not good enough, easy to fall off, and deteriorate; ⑥ The return and exhaust color steel plates are connected, and the dust enters the return air duct from the exhaust duct; ⑦ Process purified water, injection water and other stainless steel When the sanitary pipe is welded, the inner wall weld is not formed; ⑧ The check valve of the air duct fails to operate, and the air backflow causes pollution; ⑨ The installation quality of the drainage system is not up to standard, and the pipe rack and accessories are easy to accumulate dust; ⑩ The pressure difference setting of the clean room is unqualified, Can meet the production process requirements. Therefore, for each professional installation engineering company, no matter the cleanliness of clean room construction is high or low, it is necessary for the pharmaceutical factory to do a good job in the process control of the engineering part before the pollution source enters.
SUZHOU PHARMA MACHINERY CO.,LTD. thinks that customer satisfaction is one of the most important determinants of brand loyalty. High-quality service can be the difference between a one-time buyer and a lifelong repeat customer.
Compare the various types of that are available. At PHARMA MACHINERY, the range is constantly being updated with new models, technical details and competitive prices.
Overall, CUSTOM SOLUTION SERVICES may be a great way for manufacturers to expand their use of technology, but the price could present a significant hurdle for some businesses.
extraction machine CUSTOM SOLUTION SERVICES is slower than extraction machine but has a number of special applications, such as for extraction machine.